Guide · Homeowners · 4 min read · Updated 17 November 2026
Floating Staircase Types Compared: Stringer, Spine or Cantilever
Short answer
There are three main floating staircase types. A concealed stringer stair hides a steel beam in the wall and costs £6,500–£12,000. A central spine stair uses a single steel beam under the treads and costs £9,000–£18,000. Cantilevered treads anchored straight into solid masonry cost £8,000–£16,000. Your wall construction, budget and the look you want decide which suits.
Concealed stringer floating stairs
A concealed stringer is a steel beam fixed along the wall at the side of the stair. Short steel arms or plates project from it to support each tread. Once the treads are fitted, the wall is boarded or plastered over the beam so only the treads are visible, appearing to emerge from the wall. Because the steel spreads the load along its length and into the floors at top and bottom, this approach can work on a wider range of walls than pure cantilevering.
It is the most common floating stair in UK homes and usually the most cost-effective. The wall needs to be thickened slightly, often with a layer of board over the steel, and the fixings into the wall must be designed by an engineer.
Central spine staircases
A central spine stair has a single steel beam, often zig-zag or box-section, running under the middle of the treads from floor to floor. The treads sit on top, with nothing visible at the sides. It can be built away from a wall entirely, which suits open-plan rooms where the stair is a sculptural feature, and it can be designed with turns and landings.
The spine is visible, so it is part of the design. It is usually powder coated in black, white or a chosen colour, and must be fabricated precisely because every weld and joint is on show. Engineering and fabrication costs are higher, which places spine stairs at the upper end of the price range.
Cantilevered treads into masonry
A cantilevered stair has each tread, or a steel bar inside each tread, anchored directly into a solid masonry wall, commonly with chemical resin anchors. There is no visible or concealed beam: the wall itself carries the load. This creates the purest floating look, but it depends entirely on the wall being solid, thick enough and strong enough, which an engineer must confirm.
Cavity walls, timber stud walls, lightweight blockwork and walls with services or flues in the way are often unsuitable. In those cases, the designer may add steel within the wall or switch to a concealed stringer.
| Factor | Concealed stringer | Central spine | Cantilevered into masonry |
|---|---|---|---|
| Typical cost | £6,500–£12,000 | £9,000–£18,000 | £8,000–£16,000 |
| Support | Hidden steel beam in wall | Visible steel beam under treads | Treads anchored into wall |
| Wall needed | Sound wall for beam fixings | Not necessarily | Solid, suitable masonry |
| Look | Treads emerge from the wall | Sculptural, can stand free | Purest floating effect |
| Turns and landings | Possible with more steel | Well suited | More complex |
| Disruption to wall | Chasing or thickening | Minimal | Drilling and anchoring |
Choosing tread materials
Solid oak is the most popular tread for floating stairs, often 60 to 100 mm thick so the treads look substantial and can span from the support without bouncing. Walnut, ash and engineered timber are alternatives. Stone, concrete and glass treads are also possible but heavier or more specialised, and must be accounted for in the structural design. Thick timber treads are usually machined with a pocket or slot that fits over the hidden steel, so no fixings show.
Finish matters on a stair that takes daily wear. Hard-wearing oils or lacquers suited to floors protect timber treads, and an anti-slip treatment or grooves near the nosing can reduce the risk of slipping in socks.
- Solid oak in 60 to 100 mm thicknesses is the most common
- Heavier materials such as stone need allowing for in the design
- Machined pockets hide fixings inside the tread
- Floor-grade oils or lacquers protect against wear
- Anti-slip grooves or treatments improve grip
Balustrade options for each type
Whichever support you choose, the open side of the stair and the landing edge need guarding. Frameless glass, set in a channel fixed to the floor or clamped to the side of the stringer or spine, keeps the floating look and lets light through. Vertical steel rods or flat bars running from floor to ceiling, sometimes called a tension rod or rod balustrade, give a lighter industrial look and can also help stiffen the stair. A solid half-height wall is another option where privacy or a more enclosed feel is wanted.
Each choice must meet the same rules: at least 900 mm high from the pitch line on private stairs and no gaps that a 100 mm sphere could pass through. Glass needs suitable safety glass and fixings designed for the loads, and rods must be spaced closely enough to meet the gap rule.
- Frameless glass in a base channel or side clamps
- Floor-to-ceiling steel rods or flat bars
- A solid half wall along the open side
- A slim wall-mounted handrail on the wall side
Which type suits your home
If you have a sound wall alongside the stair and want the floating look at the lowest cost, a concealed stringer is usually the right choice. If you have an open-plan space and want the stair to be a centrepiece, or there is no suitable wall, a central spine stair suits. If you have a solid masonry wall an engineer is happy with, and want the cleanest effect, cantilevered treads are worth considering.
In all cases, the open side needs guarding and the stair must meet the Building Regulations. We arrange a survey and engineering advice so the type is chosen around what your building can actually support, not just the photographs.
Questions people also ask
Can floating stairs be fixed to a stud wall?
Not as pure cantilevers. Timber stud walls cannot carry cantilevered treads on their own. A concealed steel stringer can sometimes be used, with the load taken into the floor structure and the stud wall rebuilt around it, or a central spine stair can avoid the wall entirely. An engineer must design the support.
Do floating stairs bounce or wobble?
A well-designed floating stair should feel solid. Bounce usually means treads that are too thin for the span, a support that is not stiff enough or fixings that have loosened. Engineers design for both strength and stiffness, and thick treads with steel inserts help stairs feel firm underfoot.
Can a floating staircase turn a corner?
Yes. Concealed stringer and spine stairs can both include quarter or half turns, with winders or landings. Turns need more complex steelwork and accurate site measurement, which adds cost and lead time. Cantilevered stairs can also turn but depend on suitable walls at each part of the turn.
Written and checked by the Floating Staircase Builders team. Read our editorial policy.
More guides
How Much Does a Floating Staircase Cost in the UK?
A straight floating staircase with a concealed steel stringer and oak treads typically costs £6,500–£12,000 in the UK. Central spine staircases run…
Floating Staircase Building Regulations: UK Rules Explained
In England, private stairs must follow Approved Document K: a maximum rise of 220 mm, minimum going of 220 mm and maximum pitch of 42 degrees. Open…
Can My Wall Support Floating Stairs? Structural Checks Explained
Only an engineer can confirm whether your wall can support a floating staircase. Solid brick or dense block walls are often suitable for cantilevered…
Floating Staircase Installation: What Happens, Step by Step
A floating staircase project runs through survey, design and structural calculations, Building Control approval, steel and tread fabrication, removal…
Get a free floating staircase builders quote
Tell us what you need and we'll come back with a clear price.
Request a quote